Custom ACSR EN 50182 NF C 34-125 Galvanized Steel Core Aluminum Conductor Factory, Exporters

1 / 3

Custom ACSR EN 50182 NF C 34-125 Galvanized Steel Core Aluminum Conductor Factory, Exporters

Execution standard: BS EN 50182 Â (Old Standard: NF C 34-120)

Material: ACSR adopts Galvanized steel wire, AL1 aluminum.

ACSR is a versatile power transmission wire, where a robust steel core provides reliable structural backing and finely drawn aluminum wires form the outer layer for optimal conductivity. Â Its impressive tolerance to extreme conditions makes it a trusted choice for high-voltage grids.

Send Inquiry

Product Description

ACSR Standard: EN 50182 (Old Standard: NF C 34 120)

Type: AL1/ST1A

Aluminum Conductor Steel Reinforced (ACSR)
Code Name	Old Code Name	Product structure				Sectional Area			Overall Diameter	Nominal Breaking Load	Linear Mass	Maximum Resistance at 20℃	Modulus of elasticity	Coefficient of linear expansion	Direction of outside layer
		Aluminium Wire Diameter & Stranding		Galvanized steel Wire Diameter & Stranding		Aluminium	Galvanized steel	Total	Overall Diameter	Nominal Breaking Load	Linear Mass	Maximum Resistance at 20℃	Modulus of elasticity	Coefficient of linear expansion	Direction of outside layer
		mm	No.	mm	No.	mm²	mm²	mm²	mm	kN	kg/km	Ω/km	N/MM2	1/K	/
28-AL1/9-ST1A	CANNA 37.7	2.00	9	2.00	3	28.3	9.4	37.7	8.3	16.26	151.5	1.0187	88000	1.71x10-5	S
38/AL1/22-ST1A	CANNA 59.7	2.00	12	2.00	7	37.7	22.0	59.7	10.0	32.70	276.1	0.766	103500	1.54x10-5	S
48-AL1/28-ST1A	CANNA 75.5	2.25	12	2.25	7	47.7	27.8	75.5	11.3	41.15	349.4	0.6052	103500	1.54x10-5	S
59-AL1/34-ST1A	CANNA 93.3	2.50	12	2.50	7	58.9	34.4	93.3	12.5	49.48	431.4	0.4902	103500	1.54x10-5	Z
94-AL1/22-ST1A	CANNA 116.2	2.00	30	2.00	7	94.2	22.0	116.2	14.0	43.17	432.5	0.3067	75500	1.80x10-5	S
119-AL1/28-ST1A	CANNA 147.1	2.25	30	2.25	7	119.3	27.8	147.1	15.8	54.03	547.4	0.2423	75500	1.80x10-5	S
147-AL1/34-ST1A	CANNA 181.6	2.50	30	2.50	7	147.3	34.4	181.6	17.5	64.94	675.8	0.1963	75500	1.80x10-5	S
185-AL1/43-ST1A	CANNA 228	2.80	30	2.80	7	184.7	43.1	227.8	19.6	80.54	847.7	0.1565	75500	1.80x10-5	S
234-AL1/55-ST1A	CANNA 288.2	3.15	30	3.15	7	233.8	54.6	288.3	22.1	98.58	1072.8	0.1236	75500	1.80x10-5	S

Type: AL1/ST6C

Aluminum Conductor Steel Reinforced (ACSR)
Code Name	Old Code Name	Product structure				Sectional Area			Overall Diameter	Nominal Breaking Load	Linear Mass	Maximum Resistance at 20℃	Modulus of elasticity	Coefficient of linear expansion	Direction of outside layer
		Aluminium Wire Diameter & Stranding		Galvanized steel Wire Diameter & Stranding		Aluminium	Galvanized steel	Total	Overall Diameter	Nominal Breaking Load	Linear Mass	Maximum Resistance at 20℃	Modulus of elasticity	Coefficient of linear expansion	Direction of outside layer
		mm	No.	mm	No.	mm²	mm²	mm²	mm	kN	kg/km	Ω/km	N/MM2	1/K	/
94-AL1/22-ST6C	CROCUS 116.2	2.00	30	2.00	7	94.2	22.0	116.2	14.0	49.32	432.5	0.3067	75500	1.80x10-5	S
199-AL1/28-ST6C	CROCUS 147.1	2.25	30	2.25	7	119.3	27.8	147.1	15.8	61.83	547.4	0.2423	75500	1.80x10-5	S
147-AL1/34-ST6C	CROCUS 181.6	2.50	30	2.50	7	147.3	34.4	181.6	17.5	74.22	675.8	0.1963	75500	1.80x10-5	S
185-AL1/43-ST6C	CROCUS 228	2.80	30	2.80	7	184.7	43.1	227.8	19.6	92.18	847.7	0.1565	75500	1.80x10-5	S
234-AL1/55-ST6C	CROCUS 288	3.15	30	3.15	7	233.8	54.6	288.3	22.1	113.86	1072.8	0.1236	75500	1.80x10-5	S
222-AL1/76-ST6C	CROCUS 297	2.80	36	2.25	19	221.7	75.5	297.2	22.5	147.22	1206.8	0.1307	79000	1.69x10-5	S
326-AL1/86-ST6C	CROCUS 412	3.60	32	2.40	19	325.7	86.0	411.7	26.4	173.31	1576.1	0.0889	72000	1.76x10-5	Z
508-AL1/105-ST6C	CROCUS 612	3.13	66	2.65	19	507.8	104.8	612.6	32.0	231.55	2226.5	0.0570	66500	1.83x10-5	S
717-AL1/148-ST6C	CROCUS 865	3.72	66	3.15	19	717.3	148.1	865.4	38.1	319.11	3145.4	0.0403	66500	1.83x10-5	S
957-AL1/228-ST6C	CROCUS 1185	2.80	54	2.80	37	332.5	227.8	560.3	44.7	480.75	4433.6	0.0302	63000	1.83x10-5	S
957-AL1/228-ST6C	CROCUS 1185	3.47	66	2.80	37	624.2	0.0	560.3	44.7	480.75	4433.6	0.0302	63000	1.83x10-5	S

💡 Note:

1. The elastic coefficients and expansion coefficients listed in this table are applicable to France. The calculation of other conductor structure parameters shall refer to IEC61597.

2. The flow rate values listed in this table are applicable under the conditions of a frequency of 60HZ, a wind speed of 0.6m/S, sunlight exposure in France, an ambient temperature of 35℃, and a conductor temperature of 80℃. In case of special laying conditions, the flow rate values should be reduced if there is no convection Less than 30%.

Frequently Asked Questions (FAQ)

What is the EN 50182 standard for ACSR conductors?

EN 50182 is a European standard that specifies the characteristics and requirements for concentric lay stranded bare conductors for overhead lines, replacing older standards like NF C 34 120.

What is the difference between AL1/ST1A and AL1/ST6C?

These designations refer to the type of aluminum (AL1) and the grade/strength of the galvanized steel core (ST1A or ST6C). ST6C typically offers different mechanical properties, such as a higher breaking load for specific environmental conditions.

Why is steel used in the core of ACSR conductors?

The galvanized steel core provides the necessary mechanical strength and high breaking load required to support the conductor over long spans in overhead power transmission.

How does ambient temperature affect the ACSR conductor?

The electrical resistance is calculated at 20℃. High ambient temperatures or intense sunlight can increase the conductor's temperature, thereby increasing resistance and potentially reducing current-carrying capacity (flow rate).

What does "Direction of outside layer" signify?

The direction (S or Z) indicates the lay direction of the outermost wires. This is crucial for hardware compatibility and ensuring the conductor does not unwrap under tension.

Can these conductors be used in different environmental conditions?

Yes, though the table values are based on specific conditions (e.g., wind speed 0.6m/S). If laying conditions differ, such as lack of convection, the flow rate should be adjusted accordingly.

Product Detail

Custom ACSR EN 50182 NF C 34-125 Galvanized Steel Core Aluminum Conductor Factory, Exporters

Product Description

Related Products

Product Detail

Custom ACSR EN 50182 NF C 34-125 Galvanized Steel Core Aluminum Conductor Factory, Exporters

Product Description

Related Products

CE Certification ACSR AS 1513 Galvanized steel core aluminum conductor BARE CONDUCTOR Suppliers, Exporters

CE Certification ACSR ASTM B232 Galvanized steel core aluminum conductor BARE CONDUCTOR Exporter, Exporters

Custom ACSR BS EN 50182 BS 215-1 Galvanized steel core aluminum conductor BARE CONDUCTOR Manufacturer, Factory

Custom ACSR BS EN 50182 DIN 48204 Galvanized steel core aluminum conductor BARE CONDUCTOR Manufacturers, Factory

Custom ACSR EN 50182 NF C 34-125 Galvanized Steel Core Aluminum Conductor Factory, Exporters

China ACSR IEC 61089 Supplier, Factory

CE Certification ACSR AS 1513 Galvanized steel core aluminum conductor BARE CONDUCTOR Suppliers, Exporters

China AAAC EN 50182 DIN 48201 All Aluminum Alloy Conductor Manufacturer, Exporters

Custom French Standard Industrial Cables U-1000 AR2V Manufacturers, Exporters

CE Certification AAC BS EN 50182 BS 215-1 All Aluminum Conductor Factories, Exporter